The Best Plumbing Company in Atwater

I arrived at the customer's property to check a kitchen sink and bathroom tub. The kitchen sink was already fixed, so we left it alone. I then went to the bathroom to check the tub shower. I found that the handle was loose and the water was dripping because the shower valve tub handle would not shut the water down all the way. I shut the water down to the house and removed the handles to the tub shower. I found that the cartridges had tile around them. I was unable to access them, so I had to chip around the hot, cold, and diverter to remove them. Once I removed them, I was able to proceed with rebuilding the tub shower. I also replaced the tub spout and shower arm and mounted their shower hose sprayer. We also have the water back on, and there are no leaks at this time.

I was called to a home to repair a sewer line that was clogged and draining slowly. I found that the sewer line was collapsed in multiple spots, and it needed to be replaced.

Today I changed out the fluid master fill valve. The other one was hanging up and overflowing the toilet tank. I also trimmed Douglas valve tube down because it was too tall, allowing water to go to high and come out the handle. I also tightened up the bolts on the tank because it was moving around. No leaks

Arrived to find the sewer line clogged uphill from the 4” san tee on its back clean out near the back left corner of the building. Ran a mainline snake with a 3” grease cutting double blade uphill from the 4” san tee clean out behind the building and got the line to flow about 20-30 feet uphill. Ran water into the interior drains and flushed the toilets multiple times to test. The sewer line is draining at this time.

I arrived at a house to find that the bathtub wouldn't get cold water and the handle kept falling off. I adjusted the scald guard temp to get the cold water to temper properly. I gained authorization to pick up a trim kit for the price pfister tub/shower valve. I removed the old trim kit and installed a new one in its place. I ran water into the tub/shower to test. The water in the tub is hot and the handle isn't falling off at this time.

Arrived to find ROOM 32 sewer line backed up and holding water at the sewer clean out in room 31. Ran sewer cable 20’ with double 4” cutters to clear paper towels stoppage. Cleared and flowing good. Repaired toilet flange in room 32 and reset toilet that was pulled by maintenance technician.

I was called to a home to unclog a sewer main line. The toilet was not flushing properly and the customer could not locate the clean out. I used a cable to pull the toilet out and found a 4 inch clean out. I reset the toilet and the customer was able to flush the toilet.

I repaired a leaky sink in the master bedroom. I removed the old pop-up assembly and pee trap, cleaned the area, and replaced the parts with new ones. I tested the sink to ensure it was working properly.

I arrived at a home to find a kitchen sink clogged. I removed the clean out and ran a snake down the drain. I pulled back a lot of sludge on the blade and cable after running the snake all the way out. I reassembled the drain and ran water into the sink to test. The kitchen sink is draining without issue at this time.

I arrived at a home to find the kitchen sink drain clogged. I ran a junior snake into the 2” kitchen clean out to get the line to drain down and stay flowing. I ran water into the kitchen sink while I ran the snake all the way out and back multiple times to make sure the line was clear of as much debris as I could get from the line.

I was called to a home to unclog a kitchen sink and sewer main line. I used a JR machine to snake the mainline through a 1.5-inch clean out. I ran approximately 60 feet of cable up to the septic tank, but I could not find any other clean out for the mainline. I snaked the kitchen sink through a 1.5-inch clean out, which was 40 feet away. I hit a blockage at 25 feet, but I did not pull anything out. I tested the line properly after running water for 5 minutes.

I removed the old burner and gas control valve and installed new ones that were ordered under warranty. I tested all connections and there are no leaks.

Upon arrival I was shown to the left hand bathroom near the back right corner of the store and found just the toilet clogged. Everything else was draining. Ran a toilet auger into the toilet about 2.5 feet to get the toilet to flush. Pulled back some hard waste on the auger. Flushed the toilet with toilet paper in the bowl multiple times while running water into the bathroom sink to test. The toilet is flushing without issue at this time.

Arrived on property, customer stated getting a bad smells coming from the water heater located in the garage. Drained and flushed tank, water was clean. Then discovered mice droppings around tank. Cleaned it up advised customer of possible mice in the garage around tank. Water heater is working properly.

I removed and looped water lines at an old water heater and installed a one point-of-use water heater at two different bathroom sinks.

Arrived on property, customer stated having a propane gas smell under the kitchen range cooktop cabinet. I spray bubble tested all connection fittings and discovered a small gas leak at flexible gas supply line at shut off valve flared connection. Removed gas supply line and gas range regulator, reassembled everything with new gas Teflon and pipe dope compound. Tested for leaks by spraying leak detection spray at all connections, no more leaks found and cooktop is working properly.

Arrived to find 60 gallon water heater not working and giving error code low igniter current. Will send estimate to order and install new parts

I replaced the water heater straps, the gas supply valve with flex line, both the water flex supplies, and removed the copper 90s in order to install new 3/4 copper male adapters. I started the water heater and it is working at this time.

I fixed a leaky tub faucet by adjusting the stopper and performing a pressure flush on the old Moen valve. I removed the cartridge and cleaned the rust from the valve. Now the tub is holding water without any drips.

I arrived to find a kitchen sink clogged on the garbage disposal side. I reset the garbage disposal and used a disposal wrench to loosen it up. I then ran water into both sides of the kitchen sink while running the garbage disposal to test. The disposal is functioning and the sink is draining.

Found a pinhole leak on the tank water heater 3/4” galvanized nipple on the hot side water line, removed and replaced it, no more leaks found.

REPLACE 1 1/2" GALVANIZED NIPPLE IN WALL UNDER KITCHEN SINK WITH A NEW ONE.

Replace the toilet handle and flapper in the bathroom.